Black-box 5000 User Manual Page 22
- Page / 268
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
CHAPTER 2: Introduction
21
three (3) high-speed interconnect links (a
Multiserver-to-Multiserver connection) in ports A1
to A3, five (5) mux links (a Multiserver-to-feeder-
mux connection) in ports A1 to A5, or five (5) data
input/output channels in ports A2 to A6.
The high-speed interconnect or composite
channels and the mux channels support RS-232C,
V.24, and V.28 interfaces. Data-transmission speeds
can be from 1200 bps to 72 Kbps on interconnect
links or up to 19.2 Kbps on mux links. Operation is
serial synchronous, full-duplex, with internal or
external clocking.
The five I/O ports on the CCM present themselves
as DCE. They can be set up for either synchro-nous
or asynchronous data transmission.
In addition to the CCM, there are expansion and
access modules, detailed below, that let you
customize your network to your specific data
communication needs.
2.2 Feeder Muxes
The Multiserver 5000 can support up to five (5)
feeder muxes. Each feeder mux can support both
async data channels and voice/fax channels. The
following multiplexors are link-compatible with a
Multiserver:
• Communication Box II (MX003A) with one
of the following CommPak Multiplexor
Cartridges:
— Enhanced Statistical Multiplexor
(MX100A)
— Quick Stat CommPak Mux
(MX107A-R2)
• Statplex Multiplexor 4- and 8-port models
(MX611A and MX622A)
Figure 2-2. The back panel of a fully outfitted Multiserver 5000 is shown here. With the six-channel
sync/async expansion module in expansion slot B and the twelve-channel expansion module in
expansion slot C, this Multiserver 5000 could have up to 23 data channels. Ten of these data
channels could be synchronous. Expansion slot D has a two-channel voice/fax module,
allowing for all voice, fax, and data information to be sent over one leased line. The leased line
is connected to the Multiserver 5000 through the CSU/DSU module in expansion slot E.
12345 678 12345678
S1 S2
1 2 4 5 6
ALARM
GCNO
NC
115/230
VAC
1 2 3 4 5 6 7 8 9 10 11 1212
A
B
C
D
E
31 2 4 5 6
DDS SERVICE
LINE 1
KTS
OPX
SB M E SG R1 T1 R T
VOICE CHANNEL 1
LOG PORT COMMAND
12345 678 12345678
MODEM
ISU
VOICE/FAX
12-CHANNEL CEM
6-CHANNEL CEM
CCM
NMS
MODULE
KTS
OPX
SB M E SG R1 T1 R T
VOICE CHANNEL 2
3
- Multiserver 5000 1
- Table of Contents 10
- Table of Contents (continued) 10
- 1. Specifications 14
- Async Channel Characteristics 15
- Sync Channel Characteristics 15
- Multiserver 5000 (continued) 15
- MS1 Voice/Fax Cards 17
- General Specifications 17
- Analog Specifications 17
- CHAPTER 1: Specifications 18
- Signaling Specifications 18
- Digital Specifications 18
- MS1 56K CSU/DSU Module 19
- MS RLB Module 19
- MS1 NMS Module 20
- MS1 V.35 Converter/DCE 20
- X.21 Converter/DCE 20
- 2. Introduction 21
- CHAPTER 2: Introduction 22
- 2.2 Feeder Muxes 22
- 2.12 Manual Text Conventions 26
- Default Node Default Node 29
- Unit Number ID 29
- INGLE LINK POINT-TO-POINT 31
- DISTRIBUTED STAR 35
- 4. Base-Unit Installation 36
- Warning! 37
- Channel Numbers 39
- 5. Module Installation 42
- 5.4 Blank Back Panel 45
- 5.5 Disassembly Procedures 45
- NUMBER 1 47
- 5.6 Installation Procedures 49
- DIMPLES ON TOP OF BACK PANEL 51
- BLANK BACK PANEL 51
- NSTALLING CONVERTERS 53
- EMOVING CONVERTERS 53
- 6. Getting Started 54
- CHAPTER 6: Getting Started 55
- 6.3 The Command Facility 55
- 6.4 Reset Defaults 57
- 6.5 Name the Local Node 58
- 6.6 Quick Setup 60
- 1 2 3 4 5 6 7 8 9 10 11 1212 63
- EZ423 EZ423 65
- Crossover Cable 65
- 7.4 The Sync Data Channel 66
- (DTE, DB25) 67
- MS RLB COMMPAK 69
- Local Multiserver 69
- Remote Multiserver 69
- 7.6 Testing the RLB Module 70
- 7.7 Voice/Fax Channels 71
- 8.1 Types of Links 72
- 8.2 Avoid Node Duplication 72
- CHAPTER 8: Link Configuration 75
- 9. Data-Channel Configuration 84
- ONTROL SIGNALS 87
- Protocol Data Rate (bps) 91
- Multiserver DTE 93
- Constant Controlled 93
- 9.3 Asynchronous Channels 95
- Option Default Description 101
- 9.4 Copy Channel Parameters 104
- 10. Switching Configuration 108
- Option Description 109
- Important! 111
- 10.4 Synchronous Connections 113
- ODE/CLASS CONNECTION 115
- ATRIX CONNECTION 115
- Channels 116
- Parameters 117
- 10.8 Classes 120
- Async Channel 131
- 11. Administration 132
- CHAPTER 11: Administration 133
- Table 11-1. Reset Options 134
- 11.2 The Command Mode 135
- Table 11-2. The Command Mode 136
- 11.4 Messages 142
- Table 11-5. Dialog Messages 144
- 11.5 Network Security 146
- 11.6 Status/Statistics 148
- 11.7 Link Administration 156
- 11.8 Channel Administration 156
- 12. Diagnostics 159
- CHAPTER 12: Diagnostics 161
- Facility 161
- 12.5 Testing the Network 165
- 13. LCD/Keypad 167
- LCD/Keyboard Menu Flow Chart 169
- 13.2 Banner Message Display 170
- CHAPTER 13: LCD/Keypad 171
- 13.4 Menu Functions 171
- 13.5 Administration 171
- Important 172
- 13.7 Configuration 176
- Appendix A: Worksheets 177
- Display Messages Worksheet 190
- Record of Passwords 192
- Appendix B: Cabling Diagrams 193
- LEAVE A1 EMPTY 206
- RJ-48 CONNECTOR 206
- RJ-48 AT BOTH ENDS 206
- OF CABLE 206
- Cabling for the NMS Module 207
- (RS-232) 208
- CONVERTER 208
- (EHN071-005M) 210
- Cabling for Use with Tandem 212
- Appendix C: Defaults 213
- Voice/Fax Module 220
- Voice/Fax Module (continued) 221
- NMS Module 222
- Appendix D: Messages 223
- Screen Display Messages 224
- LCD Messages 236
- Appendix E: Indicators 241
- HP ENQ/ACK 247
- Table F-1. Spool Mode 248
- TOP VIEW 249
- MULTISERVER 5000 250
- Glossary 254
- Review System Message Log 266
- Menu Functions (password) 266
- Menu Flow Diagram 267
© 2020, manymanuals.com. All rights reserved. | 1.586 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals