Black-box 5000 User Manual Page 234
- Page / 268
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Multiserver 5000
232
ni TRANSMITTER RING Event A call is coming in on the transmitter side.
DETECT LINK ci
ni TX CONNECTION MADE Event A successful call was placed over the dial-lines
LINK # ci from the modem’s TX dial line connection. This
message is displayed by the call-originating modem.
<UNASSIGNED> Dialog • Node, class, module location, or port is unknown
in the network.
• Password for the class may be incorrect.
• If matrix switching is disabled, this message will
display when matrix switching is attempted.
<UNAVAILABLE> Dialog Requested resource exists, but is not in service (not
operational). Call inhibit may be off or DTR is off.
VOICE CHANNEL Event Voice/fax port c on node n has been put in a
[n/c] [condition] busyout state. [Conditions] may be the
BUSY OUT following:
System Where the link has experienced a sync
loss, a force-disable command, or a
force-disconnect command.
Forced Where the network operator has put the
channel in a busyout condition via a
forced-busy command.
VOICE CHANNEL [n/c] Event Termination of a busyout condition has
BUSYOUT CLEARED occurred on voice/fax channel c.
VOICE CHANNEL [n/c] Event The current dBm level for voice/fax port
INPUT LEVEL: nn dBm c on node n is nn (-25 to +1) dBm.
- [display] - Note: [Display] is a dynamic display
which appears on the screen.
VOICE CHANNEL [n/c] Diagnostic Voice/fax port c on node n has started the
LOCAL LOOP TEST diagnostic local loop test.
VOICE CHANNEL Event The voice/fax port has been reset and
[n/c] RESET re-initialized to the current configuration.
VOICE CHANNEL [n/c] Diagnostic Voice/fax port c on node n has completed
SELF TEST FAIL the internal diagnostic tests unsuccessfully.
VOICE CHANNEL [n/c] Diagnostic Voice/fax port c on node n has completed
SELF TEST PASS the self-tests successfully.
Screen Display Messages
Message Message Type Explanation
- Multiserver 5000 1
- Table of Contents 10
- Table of Contents (continued) 10
- 1. Specifications 14
- Async Channel Characteristics 15
- Sync Channel Characteristics 15
- Multiserver 5000 (continued) 15
- MS1 Voice/Fax Cards 17
- General Specifications 17
- Analog Specifications 17
- CHAPTER 1: Specifications 18
- Signaling Specifications 18
- Digital Specifications 18
- MS1 56K CSU/DSU Module 19
- MS RLB Module 19
- MS1 NMS Module 20
- MS1 V.35 Converter/DCE 20
- X.21 Converter/DCE 20
- 2. Introduction 21
- CHAPTER 2: Introduction 22
- 2.2 Feeder Muxes 22
- 2.12 Manual Text Conventions 26
- Default Node Default Node 29
- Unit Number ID 29
- INGLE LINK POINT-TO-POINT 31
- DISTRIBUTED STAR 35
- 4. Base-Unit Installation 36
- Warning! 37
- Channel Numbers 39
- 5. Module Installation 42
- 5.4 Blank Back Panel 45
- 5.5 Disassembly Procedures 45
- NUMBER 1 47
- 5.6 Installation Procedures 49
- DIMPLES ON TOP OF BACK PANEL 51
- BLANK BACK PANEL 51
- NSTALLING CONVERTERS 53
- EMOVING CONVERTERS 53
- 6. Getting Started 54
- CHAPTER 6: Getting Started 55
- 6.3 The Command Facility 55
- 6.4 Reset Defaults 57
- 6.5 Name the Local Node 58
- 6.6 Quick Setup 60
- 1 2 3 4 5 6 7 8 9 10 11 1212 63
- EZ423 EZ423 65
- Crossover Cable 65
- 7.4 The Sync Data Channel 66
- (DTE, DB25) 67
- MS RLB COMMPAK 69
- Local Multiserver 69
- Remote Multiserver 69
- 7.6 Testing the RLB Module 70
- 7.7 Voice/Fax Channels 71
- 8.1 Types of Links 72
- 8.2 Avoid Node Duplication 72
- CHAPTER 8: Link Configuration 75
- 9. Data-Channel Configuration 84
- ONTROL SIGNALS 87
- Protocol Data Rate (bps) 91
- Multiserver DTE 93
- Constant Controlled 93
- 9.3 Asynchronous Channels 95
- Option Default Description 101
- 9.4 Copy Channel Parameters 104
- 10. Switching Configuration 108
- Option Description 109
- Important! 111
- 10.4 Synchronous Connections 113
- ODE/CLASS CONNECTION 115
- ATRIX CONNECTION 115
- Channels 116
- Parameters 117
- 10.8 Classes 120
- Async Channel 131
- 11. Administration 132
- CHAPTER 11: Administration 133
- Table 11-1. Reset Options 134
- 11.2 The Command Mode 135
- Table 11-2. The Command Mode 136
- 11.4 Messages 142
- Table 11-5. Dialog Messages 144
- 11.5 Network Security 146
- 11.6 Status/Statistics 148
- 11.7 Link Administration 156
- 11.8 Channel Administration 156
- 12. Diagnostics 159
- CHAPTER 12: Diagnostics 161
- Facility 161
- 12.5 Testing the Network 165
- 13. LCD/Keypad 167
- LCD/Keyboard Menu Flow Chart 169
- 13.2 Banner Message Display 170
- CHAPTER 13: LCD/Keypad 171
- 13.4 Menu Functions 171
- 13.5 Administration 171
- Important 172
- 13.7 Configuration 176
- Appendix A: Worksheets 177
- Display Messages Worksheet 190
- Record of Passwords 192
- Appendix B: Cabling Diagrams 193
- LEAVE A1 EMPTY 206
- RJ-48 CONNECTOR 206
- RJ-48 AT BOTH ENDS 206
- OF CABLE 206
- Cabling for the NMS Module 207
- (RS-232) 208
- CONVERTER 208
- (EHN071-005M) 210
- Cabling for Use with Tandem 212
- Appendix C: Defaults 213
- Voice/Fax Module 220
- Voice/Fax Module (continued) 221
- NMS Module 222
- Appendix D: Messages 223
- Screen Display Messages 224
- LCD Messages 236
- Appendix E: Indicators 241
- HP ENQ/ACK 247
- Table F-1. Spool Mode 248
- TOP VIEW 249
- MULTISERVER 5000 250
- Glossary 254
- Review System Message Log 266
- Menu Functions (password) 266
- Menu Flow Diagram 267
© 2020, manymanuals.com. All rights reserved. | 0.556 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals